West Tennessee State Penitentiary CCTV System Familiarization Training

Скачать презентацию West Tennessee State Penitentiary CCTV System Familiarization Training

d1da1e767067eebd938475d8df4e2f89.ppt

Количество слайдов: 112

West Tennessee State Penitentiary CCTV System Familiarization Training

West Tennessee State Penitentiary Introduction

West Tennessee State Penitentiary Technical Support 1 -800 -34 -VICON (1 -800 -348 -4266) 8: 00 AM – 6: 30 PM Eastern Time Monday through Friday 1 -800 -645 -9116, Extension 877 After Hours and Weekends or Holidays

West Tennessee State Penitentiary Other Numbers Website http: //www. vicon-cctv. com FTP Site ftp: //ftp. vicon-cctv. com Parts Department 1 -800 -645 -9116, Ext 369 Service Department 1 -800 -645 -9116, Ext 384

West Tennessee State Penitentiary Web Site US Home Page

West Tennessee State Penitentiary FTP Site Main Screen

West Tennessee State Penitentiary FTP Software Folder

West Tennessee State Penitentiary FTP Site Sec 3 – Camera Domes

West Tennessee State Penitentiary FTP S 2000 Software Folder

West Tennessee State Penitentiary FTP SVFT Software Folder

West Tennessee State Penitentiary Data Types and Distribution

West Tennessee State Penitentiary Data Communications There are three major types of Serial Communication Standards

West Tennessee State Penitentiary Data Communications RS-232 § Unbalanced Circuit (single conductor plus ground reference) § Short Distances (typically <50 feet) § Used in Low Noise Environments § Bi-Polar Signal (voltage levels swing + and -) § Point-to-Point Communications

West Tennessee State Penitentiary Data Communications RS-422 § Balanced Circuit (two signal conductors plus ground reference) § Long Distances (typically ~4000 feet) § Excellent Noise Immunity § Signal Levels of 0. 0 vdc and +5 vdc § Point-to-Point Communications

West Tennessee State Penitentiary Data Communications RS-485 § Balanced Circuit (two signal conductors plus ground reference) § Long Distances (typically ~1000 feet) § Excellent Noise Immunity § Signal Levels of 0 vdc and +5 vdc § Multidrop Communications (Typically 32 Nodes)

West Tennessee State Penitentiary Data Communications Within each standard, there are communications types

West Tennessee State Penitentiary Data Communications Simplex This is a uni-directional form of communications. Duplex This is a bi-directional form of communications.

West Tennessee State Penitentiary Data Communications Within the Duplex mode are two further sub-divisions: Full Duplex – - This mode permits simultaneous bi-directional communications. Half-Duplex – - This mode is bi-directional also, but only one direction at a time.

West Tennessee State Penitentiary Data Communications Vicon uses both Simplex and Half-Duplex Communications Keypads must use Half-Duplex. Receiver-Drivers can use either Simplex or Half-Duplex

West Tennessee State Penitentiary Data Communications Data Signal Names used by Vicon are Command Response. Command – this signal is generated by a CPU and is sent to a peripheral device, either a Keypad or a Camera Receiver-Driver. Response – This signal is generated by a peripheral device and sent to the CPU as an answer to a Command from the CPU.

West Tennessee State Penitentiary Data Communications To comply with the RS 422 balanced circuit, there is a Positive (+) and Negative (-) side of the signals. These are called Command + and Command -, as well as Response + and Response -. Starting at the CPU, the signal lines would be called: Command Out + and Command Out -. They will connect to the peripheral device to Command In + and Command In -, respectively.

West Tennessee State Penitentiary Data Communications Connection Rules: Command always connects to Command Response always connects to Response + signals always connect to + signals - signals always connect to – signals Inputs connect to Outputs connect to Inputs

West Tennessee State Penitentiary Data Communications Some types of equipment, fiber optic modules for instance, use connection terms such as Data In + or Data Out +. In these cases, Data Out + would be the same as Command Out + or Response Out + (depending on the direction of signal flow).

West Tennessee State Penitentiary Data Communications Data Cabling For data wiring of peripheral devices, Vicon recommends the use of a dual-pair, twisted, individually shielded wire meeting the specifications of one of the cable types listed below: Belden™ 8723 West-Penn Wire ™ D 510 Alpha Wire ™ 2466 C Note: these part numbers are for PVC jacketed wire. Check manufacturer’s catalog for Plenum versions if local codes dictate.

West Tennessee State Penitentiary Data Communications Questions?

West Tennessee State Penitentiary Data Distribution V 1400 X-IDL Intelligent Distribution Line Module Provides isolated RS-422 data distribution for keypads OR receiver-drivers. 1 Input – 10 Equal Outputs

West Tennessee State Penitentiary Data Distribution V 1400 X-IDL Intelligent Distribution Line Module (earlier version shown) The later version can be recognized by the slide switch between Station connectors J 7 and J 6. This switch selects between the IDL (Intelligent) and the DL (non-Intelligent) operation. (In earlier V 1400 X-IDL’s, an internal jumper had to be removed to change operation modes)

West Tennessee State Penitentiary Data Distribution V 1400 X-IDL Intelligent Distribution Line Module Indicator LEDs Station Indicators: Normally On. Off or blinking is an abnormal condition, usually caused by incorrect Response Wiring or defective Response signals. CPU LED: Normally On. Blinks during power up cycle while it acquires the data Baud rate. Power LED: Normally On.

West Tennessee State Penitentiary Data Distribution Typical Connection: V 1400 X-IDL Output to Surveyor VFT TB 3 Output Connector J 1 – J 10 TB-3

West Tennessee State Penitentiary Data Testing

West Tennessee State Penitentiary Data Distribution Questions?

West Tennessee State Penitentiary Video Matrix Switching Systems

West Tennessee State Penitentiary Matrix Switching Systems The basic purpose of a matrix switching system is to electrically connect camera outputs to monitor inputs. The component that accomplishes this is called a Crosspoint Switcher. The crosspoint switcher is an electrical junction that, when forward biased, allows signal to flow. When reverse biased, the junction has a high impedance to signal flow.

West Tennessee State Penitentiary How A Matrix Works INPUTS 4 X 4 MATRIX OUTPUTS

West Tennessee State Penitentiary In 1 -256 Out 1 -16 In 1 -256 Out 17 -32 In 1 -256 Out 33 -48 In 1 -256 Out 49 -64 In 1 -256 Out 65 -80 In 1 -256 Out 81 -96 In 1 -256 Out 97 -112 In 1 -256 Out 113 -128 In 257 -512 Out 1 -16 In 257 -512 Out 17 -32 In 257 -512 Out 33 -48 In 257 -512 Out 49 -64 In 257 -512 Out 65 -80 In 257 -512 Out 81 -96 In 257 -512 Out 97 -112 In 257 -512 Out 113 -128 In 513 -768 Out 1 -16 In 513 -768 Out 17 -32 In 513 -768 Out 33 -48 In 513 -768 Out 49 -64 In 513 -768 Out 65 -80 In 513 -768 Out 81 -96 In 513 -768 Out 97 -112 In 513 -768 Out 113 -128 In 769 -1024 Out 1 -16 In 769 -1024 Out 17 -32 In 769 -1024 Out 33 -48 In 769 -1024 Out 49 -64 In 769 -1024 Out 65 -80 In 769 -1024 Out 81 -96 In 769 -1024 Out 97 -112 Out 113 -128 In 1025 -1280 In 1025 -1280 Out 17 -32 Out 33 -48 Out 49 -64 Out 65 -80 Out 81 -96 Out 97 -112 Out 113 -128 Out 1 -16 In 1281 -1536 In 1281 -1536 Out 1 -16 Out 17 -32 Out 33 -48 Out 49 -64 Out 65 -80 Out 81 -96 Out 97 -112 Out 113 -128 In 1537 -1792 In 1537 -1792 Out 17 -32 Out 1 -16 Out 33 -48 Out 49 -64 Out 65 -80 Out 81 -96 Out 97 -112 Out 113 -128 In 1793 -2048 In 1793 -2048 Out 1 -16 Out 17 -32 Out 33 -48 Out 49 -64 Out 65 -80 Out 81 -96 Out 97 -112 Out 113 -128 Expander Out 1 -16 Expander Out 17 -32 Expander Out 33 -48 Expander Out 49 -64 Expander Out 65 -80 Expander Out 81 -96 Expander Out 97 -112 Expander Out 113 -128

West Tennessee State Penitentiary Matrix 66 The Vicon Matrix 66 describes a family of Video Switching System components consisting of: V 1466 Video Switching System V 6680 SCC-HD Video Switching Card Cage

West Tennessee State Penitentiary Matrix 66 V 1466: This is a self-contained Video Matrix Switching System. Components: V 1466 SCPU-A, an internal CPU that controls matrix switching for up to 256 cameras and 32 monitors. It also provides data control for pan, tilt and lens functions, alarm handling and various video switching functions. V 1466 TDT-SHD, the Time/Date/Titler card to provide titling capabilities for up to 16 monitors.

West Tennessee State Penitentiary V 1466 Rear Panel, 64 x 16 Status Display Mon 1 Output Camera 33 Input J 2 Serial Printer Camera 1 Input J 1 Host Port J 4 Receiver Port J 3 Keypad Port J 9 Alarm Input 8 RU J 11 Control Out Mon 1 -16 3364 1 -32

West Tennessee State Penitentiary V 1466 Rear Panel, 64 x 32 V 1466 showing video looping cables for Cameras 33 -64. Camera 33 Termination Camera 33 Input (While required, the looping cables for cameras 1 -32 have been omitted for clarity) 33 - 1 -32 Mon 64 1 -32 33 - 1 -32 64

West Tennessee State Penitentiary Matrix 66 V 6680 SCC-HD This is a card cage that will support video switching components for up to 256 cameras by 16 monitors. The V 6680 SCC-HD requires an external CPU for video switching control and external Time/Date/Titling for the monitor outputs. The external CPU governs the system size limit.

West Tennessee State Penitentiary V 6680 SCC Card cage with two V 6610 S-1 Video Input cards and one V 6616 AMP Monitor Amp card with V 6670 X Card Extender

West Tennessee State Penitentiary V 6680 SCC-HD 160 x 16 System V 75 TR-SHD Terminators

West Tennessee State Penitentiary V 6680 SCC-HD Two styles of card cage rear panels are available: V 6610 RP-B This panel has 32 BNC’s for video inputs and 4 D-shell connectors for terminating or looping. It is used for both Camera Inputs and Monitor Outputs. 1 8 1 -8 9 -16 9 17 16 24 17 -24 25 -32 25 32

West Tennessee State Penitentiary V 6680 SCC-HD Cam 1 -8 Loop In Cam 9 -16 Loop In Cam 1 -8 Loop Out Cam 9 -16 Loop Out V 6610 RP-R This panel has 8 D-shell connectors for looping video. Cam 17 -24 Loop In Cam 17 -24 Loop Out Cam 25 -32 Loop In Cam 25 -32 Loop Out

West Tennessee State Penitentiary Card Cage Address Switch In from External CPU/CDU Out to Next Card Cage MON 33 - 1 -32 64 Rear Panel Connections, V 6680 SCC, 64 x 16

West Tennessee State Penitentiary V 6680 SCC-HD In a single-cage matrix system, camera video must either be terminated or looped to another video product. Termination: V 75 TR-SHD - terminates 8 cameras in a 15 -pin D-shell connector. Also used to terminate inputs to an Expander Card, V 6640 -SEXP V 75 T – terminates one camera with a BNC connection.

West Tennessee State Penitentiary V 6680 SCC-HD V 75 TR-SHD V 75 T Video Terminators

West Tennessee State Penitentiary V 6680 SCC-HD Video can loop out to another card cage or to another device (DVR, etc). Looping to another card cage: Use the V 66 RC-36 cables to pass 8 videos. Looping to another device: Use the V 66 RCB-24 to loop out and/or terminate.

West Tennessee State Penitentiary V 6680 SCC-HD V 66 RC-36

West Tennessee State Penitentiary V 6680 SCC-HD V 66 RCB-24

West Tennessee State Penitentiary Monitor 1 Monitors 1 -16 Monitor 17 Monitors 17 -32 Matrix 66 with V 66 RC-36 Video Looping Cables for Cameras 1 -32

West Tennessee State Penitentiary Matrix Switching Systems Questions?

West Tennessee State Penitentiary Programming Demonstration

West Tennessee State Penitentiary Peripheral Devices

West Tennessee State Penitentiary System Controls – V 1300 X-DVC / RVC

West Tennessee State Penitentiary System Controls – V 1300 X-DVC / RVC Two Operating Modes: Standalone Mode • For direct control of PTZ cameras Keypad Mode • For control of a matrix switching system

West Tennessee State Penitentiary System Controls – V 1300 X-DVC / RVC The V 1300 X-DVC must be programmed prior to use. To enter the Keypad Programming Mode: The Run-Pgm Switch can be in either position. Hold down F 1 and press SEQ To step through without changing, press SEQ To change a programming option, use the joystick. To store a change and move to the next option, press A/P. To exit the Keypad Programming Mode, press SEQ until the end of the menu is reached. The keypad will exit programming.

West Tennessee State Penitentiary System Controls – V 1300 X-DVC / RVC Programming Menu Items (Hold F 1 and press SEQ to enter): Keypad Type Speed Control Type Receiver Function Inhibit Joystick Response Profile Baud Rate Keypad Address Modify Passcodes Auto Logout Install Defaults Enter Diagnostic Mode Sngl, 1200, 1300 Fixed, 1200, 1300 No, Yes Low, Med, High 300 – 19. 2 K (9. 6 for CPU) Sngl: 0 -7 1200: CO (192) – EF(239) 1300: 1 -64 No, Mgr, UP 1 – UP 64 Off, 5 Min – 60 Min No, Yes Enter or SEQ

West Tennessee State Penitentiary System Controls – V 1300 X-DVC / RVC Run-Program Switch Power, 10 VAC J 20 Aux Connector J 29 RS 485 SW 39 Mode Dipswitch J 1 RS 422 Connections

West Tennessee State Penitentiary System Controls – V 1300 X-DVC / RVC Connections: V 1300 X-DVC, J 1 (in Standalone Mode) to SVFT, TB 3 J 1 TB 3

West Tennessee State Penitentiary System Controls – V 1300 X-DVC / RVC Connections: V 1400 X-IDL, J 1 -J 10 to V 1300 X-DVC, J 1

West Tennessee State Penitentiary Matrix System Peripherals V 1400 X-IDL Data Distribution Module

West Tennessee State Penitentiary Matrix System Peripherals DL – IDL Switch J 10 J 11 J 9 J 8 J 5 J 4 J 3 V 1400 X-IDL Data Distribution Module J 6 J 2 J 1

West Tennessee State Penitentiary Matrix System Peripherals Input Connector J 11 6. Command In + 5. Command In – 4. Ground 3. Response Out + 2. Response Out – 1. Ground V 1400 X-IDL Data Distribution Module

West Tennessee State Penitentiary Matrix System Peripherals Output Connectors J 1 -J 10 6. Response In + 5. Response In – 4. Ground 3. Command Out + 2. Command Out – 1. Ground V 1400 X-IDL Data Distribution Module

West Tennessee State Penitentiary Matrix System Peripherals V 1400 X-IDL Data Distribution Module

West Tennessee State Penitentiary Matrix System Peripherals V 1400 X-MSSV Multi-system Selector - Video Permits one Intelligent keypad to control up to eight different matrix systems

West Tennessee State Penitentiary Matrix System Peripherals

West Tennessee State Penitentiary Simple V 1400 X-MSSV Layout Matrix #1 Matrix #2

West Tennessee State Penitentiary Matrix System Peripherals Questions?

West Tennessee State Penitentiary PTZ Dome Cameras Surveyor VFT Dome Camera

West Tennessee State Penitentiary Operation

West Tennessee State Penitentiary Operation Initial Power Up

West Tennessee State Penitentiary Operation Initial Power Up Auto. Baud Detect

West Tennessee State Penitentiary Operation Typical PTZ Commands • • • Pan Tilt Zoom Control Auto Iris with Manual Override Auto Focus with Manual Override Auxiliary Relay Control

West Tennessee State Penitentiary Operation Pan & Tilt Pan and tilt are both variable speed camera operations. The joystick is what is known as a vector-solving joystick. The further the joystick is deflected, the faster the camera moves.

West Tennessee State Penitentiary Operation Lens Zoom is available in both optical (to x 22 or x 23, depending on camera model) and digital (to x 264 or x 276, depending on model).

West Tennessee State Penitentiary Operation Auto Iris with Manual Override The camera iris circuit controls the picture brightness by limiting the amount of light on the imaging device. The circuit can be set to operate in the Automatic or Manual mode. Keypad control of the A/I level can be disabled through programming.

West Tennessee State Penitentiary Operation Auto Focus with Manual Override The camera can be set to Auto Focus. This is the default setting. Use of the Focus Near or Focus Far keys will automatically place the camera into the manual focus mode. It will stay in this mode until either Zoom In or Zoom Out are activated.

West Tennessee State Penitentiary Programming

West Tennessee State Penitentiary Programming Commands PP 1 - 79 Preset Positions • Fixed positions stored in memory PP 80 – 87 32 -Step Tours • Point-to-point sequences • May include a number of commands • Can be activated manually or automatically PP 88 & 89 Autotours • Sequences that playback a previously recorded sequence of events

West Tennessee State Penitentiary Programming Commands - SVFT PP 90 PP 91 PP 92 PP 93 PP 94 PP 95 PP 96 PP 97 PP 98 PP 99 Pan-Tilt Lock Diagnostic Tour Diagnostic Screen Set Response Line Polarity (duplex only) Enter Menu Setup Mode Reset Auto. Baud Detect Feature Program Sectors Initiate Dome Reset Set Auto. Pan Left & Right Limit Stops Set Manual Pan Limits

West Tennessee State Penitentiary 90 -series Commands The 90 -series of commands can only be initiated in the Program mode. A 90 -series command, in the Run mode, will be ignored.

West Tennessee State Penitentiary 90 -series Commands PP 90 When issued, this command will lock out all pan and tilt commands from the controlling device and ‘freeze’ the camera in its present position. If an attempt is made to pan or tilt the camera, an on-screen message is momentarily displayed. Lens zoom and focus function will still work. Alarms and scheduled actions will over-ride the lockout.

West Tennessee State Penitentiary 90 -series Commands PP 91 This is a diagnostic command. Activating this command causes the camera to run through a programmed set of commands, i. e. , Pan Left, Pan Right, Tilt Up, Tilt Down, Zoom In, Zoom Out. The pattern will run continuously until halted by sending another PP 91.

West Tennessee State Penitentiary 90 -series Commands PP 92 This is a diagnostic command. It indicates various settings that correlate to camera pan, tilt, and zoom positions. This diagnostic screen can be monitored while sending commands to see if the camera is reacting correctly. The diagnostic is cancelled by sending another PP 92.

West Tennessee State Penitentiary 90 -series Commands PP 93 This will reverse the Response Signal Polarity (SVFT only). It is used when a dome’s Response communications lines have been mis-wired. The first PP 93 will reverse Response polarity and a subsequent PP 93 will toggle the polarity back.

West Tennessee State Penitentiary 90 -series Commands PP 94 This command displays the main Programming Menu. With the menu displayed, the following apply: • A/P This key will open a submenu. After changing a menu selection, it will save any changes that have been made and exit that particular submenu. • A/I This key will exit a menu or submenu without making or saving any changes. • Joystick Up-Down navigates menu items Left-Right selects options

West Tennessee State Penitentiary 90 -series Commands PP 94 Main Menu

West Tennessee State Penitentiary 90 -series Commands PP 94 Programming Tip: When in the program menu, pressing L-SPD (lens speed) on the keypad will darken the background to permit a better view of the menu screens.

West Tennessee State Penitentiary 90 -series Commands PP 95 This command resets the camera’s baud detect feature. It is used if the camera must be set to another baud rate.

West Tennessee State Penitentiary 90 -series Commands PP 96 This command is used to program dome sectors. There are 16 sectors that can be set. Using the joystick and the A/P button, sector limits can be set. Once Sectors have been set, the video can be blanked for any sectors.

West Tennessee State Penitentiary 90 -series Commands PP 97 This command is used to initiate a reset of the camera without changing any parameters. It is similar to a warm boot of a computer.

West Tennessee State Penitentiary 90 -series Commands PP 98 This command is used to set left and right limit stops for the Auto. Pan mode. Aux 2 sets the left Auto. Pan limit stop. Aux 3 sets the right Auto. Pan limit stop. Setting both limit stops to the same position clears the Auto. Pan limits.

West Tennessee State Penitentiary 90 -series Commands PP 99 This command is used to set left and right limit stops for the manual pan mode (PP 93 for the S 2000). Aux 2 sets the left Pan limit stop. Aux 3 sets the right Pan limit stop. Setting both limit stops to the same position clears the manual Pan limits.

West Tennessee State Penitentiary Questions?

West Tennessee State Penitentiary Direct Control

West Tennessee State Penitentiary Direct Control is a computer program that permits controlling a Vicon Receiver-Driver or dome camera from any PC. All functions of the Surveyor may be operated with Direct Control. The only additional requirement is an RS 232 -RS 422 converter.

West Tennessee State Penitentiary Direct Control is available at: ftp: //ftp. vicon-cctv. com/ Select the Software Folder Select Sec 03 (Camera Dome Systems) Select SVFT Dome Select Surveyor Direct Control

West Tennessee State Penitentiary Direct Control RS 232 -RS 422 Converter Vicon Part Number 1240 -5308 -00 Black. Box Corporation™ IC 473 A-F

West Tennessee State Penitentiary Flash Upgrade

West Tennessee State Penitentiary Flash Upgrade is a utility program that permits upgrading the Surveyor software revision in the field. The only additional requirement is an RS 232 RS 422 converter.

West Tennessee State Penitentiary Flash Upgrade and the software versions are available at: ftp: //ftp. vicon-cctv. com/ Select the Software Folder Select Sec 03 (Camera Dome Systems) Select SVFT Dome Select Surveyor Flash Upgrade Utility

West Tennessee State Penitentiary Questions?