M 220 repair trouble shooting for L 3

Зарегистрируйтесь, чтобы просмотреть полный документ!

РЕГИСТРАЦИЯ

M 220 repair trouble shooting for L 3 陳福 20150409

System Module Block Diagram

Can not power Ø Trouble shooting:

charging error Ø Circuit Analysis: Battery charging is controlled by a PMIC state-machine. The first step in the automated charging process determines if trickle charging is needed. Charging of a severely depleted battery must begin with trickle charging to limit the current, avoid pulling VDD down, and protect the battery from more charging current than it can handle. Once a minimum battery voltage is established using trickle charging, constant-current charging is enabled to charge the battery quickly – this mode is sometimes called fast charging. Once the battery approaches its target voltage, the charge is completed using constant voltage charging.

charging error Ø Trouble shooting: The main reason of can’t charge is I/O port connecting failure，the detailed reason is I/O port empty soldering or connecting soldering ; and the 5 pin I/O port of Micro USB connector cable loosen possibly which maybe cause connect bad, may change a USB connector cable, the detail repair flow in the following chart ：

Display error Ø Circuit Analysis: The display of M 220 used 4. 0 inch FWVGA color LCD. Its data interface include MIPI port and signal controlled lines , The digital port of LCD is driven by BBIC MSM 8210 (The several saw filters are used to Electro Magnetic Interference in the middle cycle ) , and its power supplied by VIO 2. 8 V of PMIC, and its driven circuit of backlight is supplied by the four common anode and backlight cycles of PM 8110.

Display error Ø Trouble shooting:

Camera error Ø Circuit Analysis: If can’t enter the mode or the camera is blurring screen , First check the soldering state of connector J 2402, J 2403, and confirm there is no short circuit and soldering empty ; finally confirm whether change the camera or not. If change the camera , the problem exist still , then please check these signals of working voltage and clock whether correct or not , according to the trouble , solder again or change BBIC。

Camera error Ø Trouble shooting:

Keypad error Ø Circuit Analysis: KCOL signal is a interrupt signal to BBIC when the key is pressed, and it puts high level at the initialization stage; KROW signal is a BBIC output signal, and it puts low level at the initialization stage. When a key was pressed, the keypad dome shorted the KCOL and KROW signal, in other words, the KCOL signal is pulled down by KROW signal, then give BB a interrupt signal, completed the keypad pressed function.

Keypad error Ø Trouble shooting:

Vibrator error Ø Circuit Analysis: Vibrate circuit is composed by reverse diode (PMU integrated) bypass capacity and the vibrator. In the vibrate mode, the signal VIB which come from the PMU chip is HIGH, the other side of vibrator connect GND, the vibrator is working

Vibrator error Ø Trouble shooting:

Receiver error Ø Circuit Analysis: Simulation audio signal are deal with by MSM 8210, then output to receiver by passed inductor and capacitor filter

Receiver error Ø Trouble shooting: Receiver error

Microphone error Ø Circuit Analysis: The voice signals are switched by MIC, from AU_VIN 0_N and AU_VIN 0_P to PMU , and are sent after processed.

Microphone error Ø Trouble shooting:

I/O connector Ø Circuit Analysis: The software is downloaded to M 220 project flash and to work with PC by DP, DM signals

I/O connector error Ø Trouble shooting:

WIFI/Bluetooth error Ø Circuit Analysis: WIFI/BT signal treatment via 3 IN 1 IC WCN 3620 chip

WIFI/Bluetooth error Ø Trouble shooting:

Скачать презентацию M 220 repair trouble shooting for L 3

fff278e108bf7eed5874ea47f18c098a.ppt

Количество слайдов: 23