Job Hazard Analysis Georgia Tech Objectives n

Job Hazard Analysis Georgia Tech

Objectives n Discuss the sub elements of worksite hazard analysis n Identify typical hazards in the workplace n Review various techniques that can be used to identify hazards in the workplace

Plan for Worksite Analysis n Comprehensive Facility Surveys n Change Analysis n Routine Job Hazard Analysis (JHA) n Periodic and Daily Inspections

Job Safety Analysis Worksheet Date: Title of Job/Operation: Exotic Log Number: Plant Removal Employee Name and Job Title: Division/Bureau/Section: Recreation and Parks Personal Protective Equipment Required or Recommended: Hat, gloves, sunscreen Sequence of Basic Job Steps Potential Accidents or Hazards* Analyst and Date: Approved By and Date: J. E. Smyth 2/17/06 Getting ready, driving to the site training equipment, road conditions, traffic accidents Driving conditions, driver training, wear seatbelts, check tires for proper inflation, drive with headlights on, be aware of the surroundings, use cell phone/radio, carry fire extinguisher and jumper cables Unloading Strain Slip/trip/fall Insect, animals, plants Use proper lifting techniques and obtain assistance of coworker First aid kit/training Proper PPE Know signs of heat stress and have fluids available. Take frequent breaks. Use sunscreen and wear long sleeve shorts and pants. Seek cover in inclement weather conditions. I. D. escape route At site: knowing plant location (asses site conditions and walk area) Plant contact with skin Environmental exposure Recommended Safe Job Procedures Record data Bag Plant Environmental Exposure Repetitive motion Frequent breaks Exposure to elements-Insect bites, snakes PPE and be alert Load trucks Large heavy bags Return/Unload trucks Lifting, slipping on bed on truck Struck By (SB) Struck Against (SA) Contacted By (CB) Contact With (CW) Caught On (CO) Caught In (CI) Caught Between (CBT) Fall - Same Level (FS) Use wheelbarrow and proper lifting techniques Proper PPE and lifting techniques Fall To Below (FB) Overexertion Exposure (E)

Job Hazard Analysis n A job hazard analysis is a technique that focuses on job tasks as a way to identify hazards before they occur. n It focuses on the relationship between the worker, the task, the tools, and the work environment. n After uncontrolled hazards are identified, take action to eliminate them or reduce risk.

Job Hazard Analysis n Performing a job hazard analysis is one of the best methods to develop safe work procedures for the equipment that is operated. n The JHA can also be used to train employees in the hazards associated with task and what control measures should be practiced.

JHA Team n A Job Hazard Analysis requires the cooperation of all parties involved that includes: Safety Professional n Engineers-Technical Advisor n Supervisors-Frontline Personnel responsible for making change n Employee-Person most familiar with job n

Prioritization of JHA n Jobs with the highest injury and illness rates n Jobs that have the potential to cause serious injury n Jobs in which one simple human error could cause injury n Jobs complex enough to have written instructions n Jobs that are new to you facility n Jobs that significantly had changes in process technology or procedures

Steps for JHA n Involve Employees n List, rank, and set n Review accident history priorities for hazardous jobs n Outline the steps or tasks n Conduct preliminary job review

Involvement of Employees n They have a unique understanding of the job, and this knowledge is invaluable for finding hazards. n Involving employees will help minimize oversights, ensure a quality analysis. n Get workers to “buy in” to the solutions because they will share ownership

Outline the Steps n Watch the employee perform the job and list each step as the worker takes it. n Be sure to record enough information to describe each job action without getting overly detailed. n Avoid making the breakdown of steps so detailed that it becomes unnecessarily long or so broad that it does not include basic steps.

Outline the Steps n Review the job steps with the employee to make sure you have not omitted something. n Include the employee in all phases of the analysis—from reviewing the job steps and procedures to discussing uncontrolled hazards and recommended solutions.

Identifying the Hazards n A job hazard analysis is an exercise in detective work. Your goal is to discover the following: What can go wrong? n What are the consequences? n How could it arise? n What are other contributing factors? n How likely is it that the hazard will occur? n

Common Hazards in the Workplace Stressor Hazard Type Chemical Corrosive Fire Explosion Electrical Shock Short Circuit Fire-Static Mechanical Moving Parts Failure Ergonomic Strain Toxic Noise Pressure Human Error Fatigue

Common Hazards in the Workplace Stressor Hazard Type Non Ionizing Radiation Ionizing Contact Struck By Struck Against Caught In Environment Temp. Visibility Weather Misc. Slips Trips Falls

Controlling the Hazards n The order of precedence and effectiveness of hazard control is the following: 1. Engineering controls. n 2. Administrative controls. n 3. Personal protective equipment. n

Controlling the Hazards n The most effective controls are engineering controls that physically change a machine or work environment to prevent employee exposure to the hazard. n The more reliable or less likely a hazard control can be circumvented, the better. n If this is not feasible, administrative controls may be appropriate. n This may involve changing how employees do their jobs.

Engineering Controls n Engineering controls include the following: n Elimination/minimization of the hazard n Substitution of equipment or process to decrease hazard n Isolation of the hazard with interlocks, machine guards, blast shields, or other means; and n Removal or redirection of the hazard such as with local and exhaust ventilation.

Administrative Controls n Administrative controls include the following: n Written operating procedures, work permits, and safe work practices; n Exposure time limitations (used most commonly to control heat stress and ergonomic hazards); n Monitoring the use of highly hazardous materials; n Alarms, signs, and warnings; n Buddy system; and training

PPE n Personal Protective Equipment is acceptable as a control method in the following circumstances: n n When engineering controls are not feasible or do not totally eliminate the hazard; While engineering controls are being developed; When safe work practices do not provide sufficient additional protection; and During emergencies when engineering controls may not be feasible.

JHA Exercise n We are going to perform an exercise on grinding metal casting. n Based on the steps, please identify the hazards and controls.

Summary n Worksite hazard analysis consists of: n Change analysis n JHA n Workplace inspections n Hazard Reporting n Trend Analysis n Effective programs will result in the identification of potential and existing hazards.