CHAPTER 10 Op-Amp Limitations
OBJECTIVES Describe and Analyze: • • • Input bias currents Input offset current Input offset voltage Frequency response Slew rate limitations Troubleshooting
Introduction • • Ideal op-amps have no limitations, but real ones do: Small bias currents flow into (or out of) both inputs The two bias currents are not exactly the same The differential-pair transistors at the input are not perfectly matched, causing an input offset voltage The bandwidth is not infinite
Input Bias Current: IIB Op-amps made with BJTs have a very small base current that flows into the input pins (for NPNs) or out of the inputs (for PNPs) on the order of n. A • Op-amps made with JFET front-ends have bias currents on the order of p. A • Input bias current must be considered when there are large resistor values (RS) in series with the inputs: VDROP = RS IIB • That VDROP looks like an input signal if it occurs on one input but not the other
Input Bias Current Equal resistance in series with both inputs cancels almost all the VDROP caused by IIB
Input Offset Current: IIO Let IIB+ be the bias current for the (+) input and let IIB- be the bias current for the (-) input. Then the input offset current is: IIO = | IIB+ | - | IIB- | Even if the resistances (RS) in series with the inputs are perfectly matched, there will be a voltage, call it VIS, that will look like an input signal: VIS = RS IIO for a modern bipolar op-amps can be pico. Amps To minimize VIS, use an op-amp with low IIO
Input Offset Voltage: VIO Input offset voltage comes from the slight mismatch between transistors in the differential pair at the front end of an op-amp. JFET op-amps can have more input offset than bipolar op-amps. Input offset voltage for bipolar op-amps can be in the range of milli. Volts for old clunkers like the 741, to micro. Volts, even down to nano. Volts for newer ones like the LT 1112.
Offset Compensation In production, it’s cheaper to buy a better op-amp than to buy a 10 -turn pot and pay someone to adjust it
Output Voltage Swing: VO Once VO hits the voltage rails, it clips
Output Voltage Swing Clipping also occurs if output current is too high
Bandwidth Above a certain frequency, the op-amp’s gain drops
Bode Plots: Gain vs. Frequency Bode plots show gain vs. frequency characteristics
Bode Plots • The vertical axis (Y-axis) shows gain in d. B of gain is defined to be: d. B = 20 Log(f) • The horizontal axis (X-axis) shows the log of frequency. • A decade is a frequency change of 10 to 1. On a Bode plot, the decades are evenly spaced. • The “roll-off” is how fast the gain drops as frequency increases. A typical roll-off is 20 d. B per decade. • The frequency where the op-amp’s open-loop gain (AOL) falls to 0 d. B (AV = 1) is called the “unity-gain bandwidth” (UGB) or the “gain-bandwidth product” (GBW)
Bandwidth: ACL & AOL • The closed-loop gain (ACL) of an op-amp circuit is typically much less than the open-loop gain (AOL). • On a Bode plot, ACL is a horizontal line. • At some frequency, call it f. B, the horizontal ACL line intersects the roll-off of AOL. • The frequency f. B is the bandwidth of the closed-loop circuit. • The intersection point is called the “ 3 d. B point” since at that frequency ACL will be down by 3 d. B.
Bandwidth Example of the bandwidth of a closed-loop gain
Slew-Rate (SR) • The “slew-rate” of an op-amp is the maximum rate of change of VOUT: SR = VOUT / t • To keep bias currents low, the internal currents in an op-amp are limited. Also inside the op-amp is a a few pico. Farads of capacitance. • The time it takes to charge or discharge a capacitor depends on the current: t = (C/I) V • So with C and I fixed, the slew rate is also fixed. It’s a parameter on the op-amp’s data sheet in volts per microsecond (V / s)
Slew-Rate a slew-rate of 1 V / s (not high, but better than a 741)
Slew-Rate An op-amp’s slew-rate (SR) limits the range of sinewave signals it will amplify: f. MAX = SR 106 / 2 VP) where SR is in Volts/ s, and VP is the peak amplitude of the sinewave on the output. The equation says we can use higher frequencies if we keep the amplitude low, or we can have higher amplitudes if we keep the frequency low.
Troubleshooting • As always, check to see if DC voltages are within the correct range. • If an op-amp needs to be replaced, use the same part number if possible. • An op-amp with better specs can usually replace a unit with worse specs (almost anything is better than a 741). But be careful: if the new op-amp has a much higher bandwidth than the original, the circuit might oscillate. • If bread-boarding a new circuit, estimate the parameter values you need for the circuit (slew rate, input offset voltage, etc) and compare them to the op-amp’s data sheet.
Скачать презентацию CHAPTER 10 Op-Amp Limitations OBJECTIVES Describe and
566f3473cb744403a4904562a681c7de.ppt